DS3900s
I discovered two DS-3900s in one of my less utilized data centers. Is the DS-3900 still supported? I'm thinking it is not.
View Articlehow to configure snmp v3 in a Director 48000 with FOS 6.3
I need to configure SNMP v3 in 2 Directors 48000 in order to allow Internal auditors to monitor some activities. I do not know how to implement V3 in these Fiber channel switches running FOS 6.3. Can...
View ArticleUsing the USB for DCX OS Upgrade
I can't get to my FW on the USB. I need to upgrade from v6.xx to v7.1 xx. I have tried a Brocade USB and 2 others. I've read the OS v6.4 and v7.x USB documentation. I tried using the GUI to activate...
View Articleconnectivity design
Hi, I have a client who has the following kit: Bladecenter H - 2 Brocade 8GB switches Bladecenter H - 2 Brocade 4GB switches FC SAN connected directly to each FCSW in both bladecenters 2 TOR IBM...
View Articlecan anyone explain the detailed reasons for 'too long' errors?
we have a 5100 connected to a Ciena DWDM and are seeing many CRC errors in conjunction with the same number (ish) of 'too long' errors being displayed when we run porterrshow. too long = Frames longer...
View ArticleFirmwaredownload failed Out of disk space....
Hello I'm trying to upgrade an 4024 blade switch to 6.2.2.f, but if fails because there's not enough space on the secondary partition Filesystem 1k-blocks
View Articleportloginshow - Device not present
I have a AIX server with HBA connected to a switch port. Switch port shows online and Healthy. But, when i use portloginshow it throws me below error. I also saw lot of link errors in the server end....
View ArticleBrocade SilkWorm 4024_interface disabled - how to enable it
Hello Everyone. I have bought Brocade 4Gb San Switch SilkWorm 4024 on ebay and I can't manage it using ILO of C7000. When I want to clik on Menagment url (IP: 10.94.26.201) of this san switch I...
View ArticleBrocade M6505 is on NO_Sigdet state
I cannot map server to any port in both AG mode and native mode because port status show No_SigDet. How can I solve it. I already install server module and driver of fabric card on OS. Port of server...
View ArticleThe factory has collapsed after the Switch, which had previously been turned...
The factory consists of five switch modules (version 6.2.2.d at all, 200e 2040 model) 4020 was some time off, at which time the factory was changed, introducing new zone and alies. After switching on...
View ArticleInteropmode issue with McDATA switch
I have configured Brocade switch with interopmode 2 to migrate McDATA (McDATA Fabric mode)... I am getting E-port segmented with zone conflict message on Brocade LabSGP:FID128:admin> switchshow...
View Articleis there a way to audit operations performed via Webtools?
Hi there, with command clihistory we can audit the last commands executed via CLI, but is there a equivalent log/command to audit the operations performed via webtools? Cheers, Felipon
View ArticleWhat is the roles and responsibilities of prinicipal switch?
What is the roles and responsibilities of prinicipal switch?
View ArticleReplacing two DS-4100 switches with two DS-5100B switches help.
I'm reaching out for assistance regarding the replacement of two EMC Branded Brocade Departmental Switches DS-4100's with two new DS-5100B switches. Is anyone aware of an actual procedure that is...
View ArticleHPAJ764A -> QLE2562 Problems.
Hi, I have a HPAJ764A -> QLE2562 card on a Linux RH5 and it only logs in the fabric (brocade 4100) if we force the speed to 2GB and it only work for few minutes and then it goes In_Sync again, can...
View ArticleBrocade 8000 enable IDLE timeout in cmsh mode
In FOS Native mode, we know the command "timeout" to set IDLE mode = timevalue or 0 to disable login timeout. try to find for the same or equivalent command when the switch is set in "cmsh" mode, but...
View ArticleBrocade 300 FOS7.1 ipv6 gateway configuration
Hello, its first time i try to create ipv6 ip addresses. I found the procedure via CLI and web tools how to create ipv6 management address+subnetmask but i have not found a way to configure ipv6...
View ArticlePorts info list of full DCX
Hi, I need a ports info list preferably in XLS or TXT or CSV format, can you send me me or point me for a full size 8 blade x 48 port DCX. I need director port numberblade numberblade port numberSCSI...
View Articlefabric on model 300
Hi, i have problem with two switches model 300. I need this switches connect to fabric. Domain IDs are 1 for SW001 and 2 for SW002 My licenses on both swithes: SW001:admin> licenseshow...
View Article